- 您现在的位置：买卖IC网 > Sheet目录1253 > XR16M890IL32-0C-EB (Exar Corporation)BOARD EVAL XR16M890IL32
XR16M890
UART WITH 128-BYTE FIFO AND INTEGRATED LEVEL SHIFTERS
REV. 1.0.0
1.11
Auto RTS (Hardware) Flow Control
Automatic RTS hardware flow control is used to prevent data overrun to the local receiver FIFO. The RTS#
output is used to request remote unit to suspend/resume data transmission. The auto RTS flow control
features is enabled to fit specific application requirement (see Figure 15 ):
? Enable auto RTS flow control using EFR bit-6.
? The auto RTS function must be started by asserting RTS# output pin (MCR bit-1 to logic 1 after it is enabled).
If using the Auto RTS interrupt:
? Enable RTS interrupt through IER bit-6 (after setting EFR bit-4). The UART issues an interrupt when the
RTS# pin makes a transition from low to high: ISR bit-5 will be set to logic 1.
1.12
Auto RTS Hysteresis
With the Auto RTS function enabled, an interrupt is generated when the receive FIFO reaches the selected RX
trigger level. The RTS# pin will not be forced HIGH (RTS off) until the receive FIFO reaches one trigger level
above the selected trigger level in the trigger table ( Table 10 ). The RTS# pin will return LOW after the RX FIFO
is unloaded to one level below the selected trigger level. Under the above described conditions, the M890 will
continue to accept data until the receive FIFO gets full. The Auto RTS function is initiated when the RTS#
output pin is asserted LOW (RTS On). Table 4 below explains this when the Trigger Table-C ( Table 10 ) is
selected.
T ABLE 4: A UTO RTS (H ARDWARE ) F LOW C ONTROL
R X T RIGGER L EVEL
8
16
56
60
INT P IN A CTIVATION
8
16
56
60
RTS# D E - ASSERTED (H IGH )
(C HARACTERS IN R X F IFO )
16
56
60
60
RTS# A SSERTED (L OW )
(C HARACTERS IN R X F IFO )
0
8
16
56
20
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
XR18W750/753-0B-EB
EVAL BOARD FOR XR18W750/753
XRP2526EVB
BOARD EVAL POWER SWITCH XRP2526
XRP2528EVB
BOARD EVAL POWER SWITCH XRP2528
XT800SM
GAS TRIGGER TUBE 800V SMD
YMCRPR8C25
REF PLATFORM MOTOR CTRL R8C/25
ZB3251
INLINE FUSE HOLDER PLASTIC BODY
ZB3260
INLINE FUSE HOLDER BAKELITE BODY
ZB3270
PANEL MOUNT FUSE HOLDER
相关代理商/技术参数
XR16M890IL32-F
功能描述:UART 接口集成电路 1-Ch 8 Bit/VLIO UART w/Lvl Shftrs & 4GPIO
RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR16M890IL32TR
制造商:EXAR 制造商全称:EXAR 功能描述:UART WITH 128-BYTE FIFO AND INTEGRATED LEVEL SHIFTERS
XR16M890IL32TR-F
功能描述:UART 接口集成电路 1-Ch 8 Bit/VLIO UART w/Lvl Shftrs & 4GPIO
RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR16M890IL40
制造商:EXAR 制造商全称:EXAR 功能描述:UART WITH 128-BYTE FIFO AND INTEGRATED LEVEL SHIFTERS
XR16M890IL40-0C-EB
功能描述:UART 接口集成电路 EVAL F/M890 QFN40 MOT, INTEL, VLIO INT RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR16M890IL40-F
功能描述:UART 接口集成电路 1-Ch 8 Bit/VLIO UART w/Lvl Shftrs & 8GPIO
RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR16M890IL40TR
制造商:EXAR 制造商全称:EXAR 功能描述:UART WITH 128-BYTE FIFO AND INTEGRATED LEVEL SHIFTERS
XR16M890IL40TR-F
功能描述:UART 接口集成电路 1-Ch 8 Bit/VLIO UART w/Lvl Shftrs & 8GPIO
RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel